Tyco Collector's Forum -
Welcome to the forum.
Username:
Password:
Save Password


Register
Forgot your Password?
  Home   Forums   Events Calendar   Forum Admins & Mods   FAQ   Install Search Provider   Register
Active Topics | Active Polls | Newsletters | Member Map | Members | Online Users |
[ Active Members: 0 | Anonymous Members: 0 | Guests: 17 ]  [ Total: 17 ]  [ Newest Member: PvtDoughnutt ] Select Skin:
 All Forums
 The Builders Depot
 Customizing & Kitbashing
 What wire to use...
   All users can post NEW topics in this forum
   All users can reply to topics in this forum
 Printer Friendly
Author Previous Topic: Talk about  Topic Next Topic: Spectrum B&O EM-1 #7614, an train made from JUNK!l  

DaCheez
Big Boy



Nose

Status: offline

 Posted - April 02 2012 :  11:53:59 AM Link directly to this topic  Show Profile  Click to see DaCheez's MSN Messenger address  Add DaCheez to Buddylist
I have several engines (mostly Tyco) lying around that are in need of re-wiring. What kind of wire do you guys use? (gauge, brand, etc,...)
 Country: Canada  ~  Posts: 3415  ~  Member Since: September 22 2006  ~  Last Visit: June 11 2025 Alert Moderator 

EM-1
Big Boy


B&O EM-1 7614

Status: offline

 Posted - April 02 2012 :  1:11:40 PM Link directly to this reply  Show Profile  Click to see EM-1's MSN Messenger address  Send EM-1 a Yahoo! Message  Add EM-1 to Buddylist
I use normally 22 to 26 gauge wire (I think that what it is!) and its flexible, and strong for the most part.

Brand, most are all the same, make sure that its BRAIDED! Not single strand....

HTH

~John

Many have tried to, and failed, ya just can't repair stupid...

Do NOT try to Idiot-Proof anything!!!! God, will simply create a better......IDIOT!
 Country: USA  ~  Posts: 2911  ~  Member Since: March 26 2012  ~  Last Visit: January 14 2014 Alert Moderator  Go To Top Of Page

microbusss
Big Boy





tiger

Status: offline

 Posted - April 02 2012 :  1:19:47 PM Link directly to this reply  Show Profile  Add microbusss to Buddylist
hey thanks EM-1 I was curious myself what it was
So what wire should I use when hooking up accesories & the like?

Edited by - microbusss on April 02 2012 1:20:29 PM
 Country: USA  ~  Posts: 14908  ~  Member Since: February 23 2009  ~  Last Visit: June 24 2025 Alert Moderator  Go To Top Of Page

DaCheez
Big Boy



Nose

Status: offline

 Posted - April 02 2012 :  1:31:37 PM Link directly to this reply  Show Profile  Click to see DaCheez's MSN Messenger address  Add DaCheez to Buddylist
Thanks for the tips! I'm going to pick up supplies tomorrow and then I have a long line of engines that need attention
 Country: Canada  ~  Posts: 3415  ~  Member Since: September 22 2006  ~  Last Visit: June 11 2025 Alert Moderator  Go To Top Of Page

EM-1
Big Boy


B&O EM-1 7614

Status: offline

 Posted - April 02 2012 :  10:43:35 PM Link directly to this reply  Show Profile  Click to see EM-1's MSN Messenger address  Send EM-1 a Yahoo! Message  Add EM-1 to Buddylist
quote:
hey thanks EM-1 I was curious myself what it was
So what wire should I use when hooking up accesories & the like?

Originally posted by microbusss - April 02 2012 :  1:19:47 PM



Well on a layout for the accesories & the like, I'd use alittle more heavy gauge wire.....I'd use something like 18 gauge to 20 gauge wire for layout wiring. That will allow you too be able to carry more Amperage, and voltage as needed. NOW if your wiring something like the track, run a "bus" wire all the way around under the layout for the left rail and then a separte one for the right rail. And run "leads from your rail, through the bench work to the bus wire you just run. The leads can be or should be less gauge then the bus! The bus carries supply, the leads only transfer it a short distance to the rail.

Lighting on the layout can be done much the same what you wire a locomotive as your not needing as much amperage. Volts remain the same but the amps will be less on lighting then on a motor draw.

A good practice, that I have used, is to use "Cat-5 or Cat-6 cable which is used for data transfer like the wire in a DSL cable that plugs into your computer for internet access! WORKS GREAT! My whole layout uses this for multiple things, on a large number of applications. Which I think is 20 gauge wire, braided.

HTH

~John

Many have tried to, and failed, ya just can't repair stupid...

Do NOT try to Idiot-Proof anything!!!! God, will simply create a better......IDIOT!
 Country: USA  ~  Posts: 2911  ~  Member Since: March 26 2012  ~  Last Visit: January 14 2014 Alert Moderator  Go To Top Of Page

NickelPlate759
Big Boy



Rivarossi Logo

Status: offline

 Posted - April 03 2012 :  4:34:56 PM Link directly to this reply  Show Profile  Add NickelPlate759 to Buddylist
I use wire salvaged from old electronics for loco wiring. I've heard people recommend wire from old corded mice being flexible and good for connections to trucks or between engine and tender, but I haven't tried it myself.
The Tyco Depot
 Country: USA  ~  Posts: 3927  ~  Member Since: June 20 2007  ~  Last Visit: November 19 2015 Alert Moderator  Go To Top Of Page
  Previous Topic: Talk about  Topic Next Topic: Spectrum B&O EM-1 #7614, an train made from JUNK!l  
 Printer Friendly
Jump To:
 Image Forums 2001 This page was generated in 0.19 seconds. Powered By: Snitz Forums 2000